South London Network merged with London to Brighton.

[danny3]

Thank you, although I do have the same documents , but will double check those speed signs in that area, but I don't really want to make drastic changes to track, speed signs might be ok to change (but just in case I'd thought i would mention that ), but i'm hoping to make the route final before the end of this week depending on free time.

From the Sectional appendix page the Speed increases at the same point on the Down Brighton Fast and the Down Brighton Slow.

I was running a scenario the other day and there appears to be a missing Signal on the Down Slow approaching Gatwick Airport.
It's where the PSR Warning board is and the signal is there on the Down Fast but not on the Slow.

The signal is strange, but its now been added, thank you for spotting that! (T229 wasn't placed but had an AWS Ramp for it!) and have updated the speed limits at London Victoria (along with speed signs too!), but these seem to have been from London - Brighton (so it could have been perhaps in 2012 it might have been different on the plans perhaps (I didn't do the track for London - Brighton).

[AndyUK]

Danny,

On the subject of AWS and signals the following signals don't have AWS ramps in the version of the route I've got:

L549 & L553 on the Down Slow approaching New Cross Gate, and the next signal L559 which is at the country end of New Cross Gate Platform 2.

You might already have this in hand but when I wanted to create a northbound scenario there were no start locations showing in the editor south of South Croydon. Adding those south of there from the L2B route would be a great help if you could do it.

Keep up the good work, it's a great addition to the Workshop!

Andy L

[danny3]

Thank you for those, they have now been fixed for the missing AWS ramps (although for the quick drive i wasn't going to add many more only because of the time taken to do the rest of the stations, free time and other things too, but luckily New Cross Gate was a fairly quick one as it was already mentioned in the player spawn points and i just happened to be online at the time )

[AndyUK]

Thanks Danny but just to be clear I wasn't talking about extra QD start points, although they would be good, but locations in the list on the first screen you see when creating a new scenario in the scenario editor.

Andy L

[danny3]

Thanks Danny but just to be clear I wasn't talking about extra QD start points, although they would be good, but locations in the scenario editor locations list.

Andy L

Ah fair enough and sorry I misread what you said and made an assumption but, that one unfortunately in locations list it will only show the locations from the route it was started from which in this case is the South London Network so will only show the route markers from that route. (you could copy over the London - Brighton ones and place them in the same folder as the South London Network assets and that should work? )

Or just place these files in the Assets\RSC\SouthLondonLines folder (I can't put these on workshop but they are only marker files) hope this helps )

http://www.alienworlds.co.uk/mainsite/u ... arkers.zip

[AndyUK]

...Or just place these files in the Assets\RSC\SouthLondonLines folder (I can't put these on workshop but they are only marker files) hope this helps )

http://www.alienworlds.co.uk/mainsite/u ... arkers.zip

Thanks again Danny, I've now got a list of locations to select from covering the whole route .

Andy L

[fsafranek]

Do I need to own the two routes already for this to work since you mention at least one is by DTG.

[michaelhendle]

Hi Frank,
you need the original LBE and the New South London Network for this to work,as it merges the two together,it then allows you to drive from London Bridge to Brighton.

Mike

[Trev123]

You need both the London to Brighton and the South London Network routes for this to work.

[PaulH2]

Quick question, and apologies if I'm being overly naïve here, but is it possible to copy over scenarios from the original London to Bright route to the merged route? I've tried a couple, and they show in TS2015 after loading and saving in RW_TOOLS, however when the scenarios load, I'm getting multiple errors.

Is there a step I'm missing, or is this not possible?

Thanks,

Paul

[Rogge]

How do i download this?

I have subscribed on Steam Workshop but cannot see any download link, i only see the button that says Subscribed.

[michaelhendle]

Hi
Once you see subcribed it will automaticaly down load to your Railworks folder.run TS2015,when it's loaded click on Profile.then workshop,it should show up on there.

Mike

[Rogge]

Once you see subcribed it will automaticaly down load to your Railworks folder.run TS2015,when it's loaded click on Profile.then workshop,it should show up on there.

Thank you, that did the trick!

[danny3]

just to note there is now an update which includes hove station (well as good as i can get without new models) and minor changes. There will probably one more update before becoming finalised with corrections to some signals (nothing major).

forgot pictures - http://alienworlds.co.uk/blog/2014/11/2 ... n-updates/

[37114]

just to note there is now an update which includes hove station (well as good as i can get without new models) and minor changes. There will probably one more update before becoming finalised with corrections to some signals (nothing major).

forgot pictures - http://alienworlds.co.uk/blog/2014/11/2 ... n-updates/

Hi Danny,

Thanks for your brilliant work, looking forward to writing some scenarios for it when you finalise. Don't know if you've done so already but adding scenery at Reigate would be a nice relatively easy win given that it's a starting and terminating point for services from and to Victoria and London Bridge.