Posted: Fri May 05, 2006 9:03 pm
looking very good i like the deatil put into the junc box
Code: Select all
File ID: 14549 Name:LMR LocosCode: Select all
File ID: 14548 Name:LMR Activites Dave R
Page 10 of 13
Posted: Tue May 16, 2006 10:16 am
I have up loaded the LMR Pack now here
I have also uploaded them to my website.
Dave R
Dave R
Posted: Tue May 16, 2006 3:12 pm
|
|
Posted: Fri Jun 02, 2006 10:10 am
do any one have any problems with the locos or the activites
Posted: Tue Jun 13, 2006 10:00 am
Yes I Have A Problem With Both I Install Them From The Zipped File But Then They Dont Work Please Could Someone Help Me back ontwomanydjs wrote:do any one have any problems with the locos or the activites
Track PS. What Is Your Website
Posted: Tue Jun 13, 2006 4:20 pm
Hmmm. Not sure about that. I had a small problem with the Signal Box activity, but I rectified this by adding a new track piece under the 'box, as the original seemed to have disappeared 
. As for the other activities, and the engines, I don't know. The steamers are a quite challenging to drive, but they're fine once you've got used to them. Does the route load on your sim in explore mode?
. As for the other activities, and the engines, I don't know. The steamers are a quite challenging to drive, but they're fine once you've got used to them. Does the route load on your sim in explore mode?Posted: Tue Jun 13, 2006 4:43 pm
Any chance of expanding on 'they don't work'? We can hardly help you based just on that.ts2005 wrote:Yes I Have A Problem With Both I Install Them From The Zipped File But Then They Dont Work Please Could Someone Help Me back ontwomanydjs wrote:do any one have any problems with the locos or the activites
PS. What Is Your Website
David
Posted: Tue Jun 13, 2006 7:02 pm
I like the new activities and rolling stock, particularly the diesel engine start thing. All the activities work except the signal box one. MSTS just crashes. Any suggestions?
Posted: Tue Jun 13, 2006 8:29 pm
Well Once They Are Installed I Then Launch MSTS And Go To Any Activity And The Engine & Consist Box Are Blankrwaceyw wrote:Any chance of expanding on 'they don't work'? We can hardly help you based just on that.ts2005 wrote:Yes I Have A Problem With Both I Install Them From The Zipped File But Then They Dont Work Please Could Someone Help Me back ontwomanydjs wrote:do any one have any problems with the locos or the activites
PS. What Is Your Website
David
What Is Your Website Address Also??
Tom Smith
Posted: Tue Jun 13, 2006 8:30 pm
Well Once They Are Installed I Then Launch MSTS And Go To Any Activity And The Engine & Consist Box Are Blankrwaceyw wrote:Any chance of expanding on 'they don't work'? We can hardly help you based just on that.ts2005 wrote:Yes I Have A Problem With Both I Install Them From The Zipped File But Then They Dont Work Please Could Someone Help Me back ontwomanydjs wrote:do any one have any problems with the locos or the activites
PS. What Is Your Website
David
What Is Your Website Address Also??
Tom Smith
Posted: Wed Jun 14, 2006 10:33 am
well i will look in to the signal box activite as it work for me when i set it all up.
To drive the steamers you just have to open the regulator to about 10% to get going then drop the cut off to about 45% and open the regulator to about 25% but do it slowly and keep an eye on the steam useage as you open the regulator cos it will jump around but then carm down to just below the generated amount.
And my website is http://www.freewebs.com/robbo25/
Hope this helps.
Dave R
To drive the steamers you just have to open the regulator to about 10% to get going then drop the cut off to about 45% and open the regulator to about 25% but do it slowly and keep an eye on the steam useage as you open the regulator cos it will jump around but then carm down to just below the generated amount.
And my website is http://www.freewebs.com/robbo25/
Hope this helps.
Dave R
Posted: Wed Jul 05, 2006 10:07 pm
i have the same problem,also i have a heap of error messages that come up, reffering to the littlemoor trains/consists.any ideas, i have deleted and reloaded many times,but with no sucess.
Posted: Thu Jul 06, 2006 2:40 pm
I am having the same problemfitwal wrote:i have the same problem,also i have a heap of error messages that come up, reffering to the littlemoor trains/consists.any ideas, i have deleted and reloaded many times,but with no sucess.
ANY HELP???
Tom Smith
post subject
Posted: Thu Jul 06, 2006 4:23 pm
I was prompted to have another look at this route after reading the foregoing messages.
The activities all seem to run OK - after remembering to start up the small ejector. This is with full graphics and with aol internet running in the background.
But the Signal Box activity will not load. Shortly after the loading bar starts with " Setting up the simulation" I get the blue screen and Send/Don't send
The activities all seem to run OK - after remembering to start up the small ejector. This is with full graphics and with aol internet running in the background.
But the Signal Box activity will not load. Shortly after the loading bar starts with " Setting up the simulation" I get the blue screen and Send/Don't send
Posted: Wed Jul 19, 2006 3:38 pm
When I had the problem, I found that the Signal Box View is an engine, as im sure you all probably know.
When i went on activity editor, i found that the path used by the 'box was missing, and there was no track under the signal box either.
So i went into route editor, replaced the track, put in a new path and it worked fine.
Only problem was you had to move the Signal Box View to suit it to the 'box, so it looked realistic.
I hope this helps
Rbridge
When i went on activity editor, i found that the path used by the 'box was missing, and there was no track under the signal box either.
So i went into route editor, replaced the track, put in a new path and it worked fine.
Only problem was you had to move the Signal Box View to suit it to the 'box, so it looked realistic.
I hope this helps
Rbridge