PLEASE READ THIS If you have or have had Hull freight on YCR

systema · Post by **systema** » Fri Feb 01, 2008 9:11 pm

Hard drive speed and a good graphics processor plus a reasonable processor are also required.

But BIN will help- have installed it yet? The latest version works fine.

Mick Clarke

bharrison · Post by **bharrison** » Mon Feb 04, 2008 10:36 am

Whats the latest version and I'll tell you If I have It?

Ben

systema · Post by **systema** » Mon Feb 04, 2008 12:55 pm

Its 1.7.102222

Go to your MSTS folder, right click on train.exe, click on properties, click on the version tab, click on file version in the drop down menu and you should see which BIN file you have.

Mick Clarke

bharrison · Post by **bharrison** » Mon Feb 04, 2008 3:42 pm

I've pulled down the latest stable patch and 1.7.10222 which is not set as stable on the website.

Is 1.7.10222 stable

Ben

systema · Post by **systema** » Mon Feb 04, 2008 5:23 pm

Is 1.7.10222 stable

Had installed since it was released without any problems.

Mick Clarke

alanch · Post by **alanch** » Mon Feb 04, 2008 6:23 pm

In certain circumstances with 1.7.10222 you can get stuck with a zero mph speed limit, which is a problem if you are driving an engine that automatically applies the emergency brake when you exceed the limit. It appears to happen if you stop at a signal and then get a green where the route doesn't reset the track limit once you pass the signal.

There are some reported problems with reduced power from multiple units - it may only use the power of the driven unit.

systema · Post by **systema** » Mon Feb 04, 2008 7:26 pm

In certain circumstances with 1.7.10222 you can get stuck with a zero mph speed limit, which is a problem if you are driving an engine that automatically applies the emergency brake when you exceed the limit. It appears to happen if you stop at a signal and then get a green where the route doesn't reset the track limit once you pass the signal.

There are some reported problems with reduced power from multiple units - it may only use the power of the driven unit.

Well, Ive never experienced any of these or heard of them reported anywhere before.

But, if you are unhappy with any version of Bin its easy enough to revert back to another version or the default Train.exe

Just give it a go, you won't regret it.

Mick Clarke

alanch · Post by **alanch** » Mon Feb 04, 2008 8:24 pm

Hi Mick

The 0 mph problem has been reported on the Bin site and on Trainsim.com - I've had it happen to me a couple of times, and for one activity on a virtual railroad (Cascade and North Western) I had to revert to the stable version because they wouldn't accept my activity summary as it showed I had been speeding!

As you say, it is very easy to change versions - I keep several ready to install.

bharrison · Post by **bharrison** » Mon Feb 04, 2008 9:35 pm

So you'd go with the latest stable patch then Alan. I ain't installing anything If it gonna goof up the pc

Ben

alanch · Post by **alanch** » Mon Feb 04, 2008 10:23 pm

Hi Ben

Horses for courses - I used the latest version for quite a while, and love the new 4 view, but when I get problems I can always revert back to the stable version. It only takes a few minutes to change versions.

dkightley · Post by **dkightley** » Mon Feb 04, 2008 10:26 pm

Bear in mind that if you use electric power, then the latest stable version has the zero power bug...like some setups, you have no power at all.

The WIP version has this problem cured...

systema · Post by **systema** » Tue Feb 05, 2008 12:03 am

Bear in mind that if you use electric power, then the latest stable version has the zero power bug...like some setups, you have no power at all.

The WIP version has this problem cured...

As I keep saying, the latest (so-called none stable) version is fine and in fact works better than the stable version excepting the possibility of the 0mph bug.

BIN will not mess up your MSTS whatever version you use. You may experience some minor glitches with earlier versions.

Anyway, I think this thread has wandered a long way off topic. All Ben wants to do is be able to get past Scarborough with the Hull Freight. Please install the latest BIN and let me know if solves your problem.

Mick Clarke

bharrison · Post by **bharrison** » Tue Feb 05, 2008 10:28 am

Will Try that. Whats the link for this wip bin so I look at that 1 to.

All the posts in this thread are related to this run In small ways

Ben

systema · Post by **systema** » Tue Feb 05, 2008 1:01 pm

http://mstsbin.uktrainsim.com/eng/eng.html

Just go to the download page.

Mick Clarke

bharrison · Post by **bharrison** » Wed Feb 06, 2008 12:11 pm

Bin patch 1.7.10222 is Bad it lauches your locos through the train your connecting to. It came straight out and the stable one went In. It won't be used again.

Ben

Atomic Systems

PLEASE READ THIS If you have or have had Hull freight on YCR

Re: PLEASE READ THIS If you have or have had Hull freight on YCR

Re: PLEASE READ THIS If you have or have had Hull freight on YCR

Re: PLEASE READ THIS If you have or have had Hull freight on YCR

Re: PLEASE READ THIS If you have or have had Hull freight on YCR

Re: PLEASE READ THIS If you have or have had Hull freight on YCR

Re: PLEASE READ THIS If you have or have had Hull freight on YCR

Re: PLEASE READ THIS If you have or have had Hull freight on YCR

Re: PLEASE READ THIS If you have or have had Hull freight on YCR

Re: PLEASE READ THIS If you have or have had Hull freight on YCR

Re: PLEASE READ THIS If you have or have had Hull freight on YCR

Re: PLEASE READ THIS If you have or have had Hull freight on YCR

Re: PLEASE READ THIS If you have or have had Hull freight on YCR

Re: PLEASE READ THIS If you have or have had Hull freight on YCR

Re: PLEASE READ THIS If you have or have had Hull freight on YCR

Re: PLEASE READ THIS If you have or have had Hull freight on YCR